Center CB tap connector is made from copper. Center brand compression fitting is manufactured in the UK to EN1254-2. Compression fitting create a mechanical joint when tightening the nut, compressing the ring onto the tube. It is compatible with copper tube manufactured to BS EN 1057.

Center FF CB 90° compression bent tap connector 15mm x 1/2"

This VSH Tectite Classic T62/T063 15mm x 1/2" 90° bent tap connector is made of brass with push-fit x BSP union nut connections. The original Tectite fitting, Tectite Classic is an ideal choice for applications requiring a demountable fitting.

Pegler VSH Tectite Classic T63 bent tap connector 15mm x 1/2in

Compact and lightweight, this Center CB end feed 90° bent tap connector with 15mm end feed x 1/2" threaded connections is designed for ease of handling and straightforward installation, even in awkward spaces. A smooth design helps to minimise flow restrictions while also ensuring the fitting looks neat when installed on exposed pipelines. Center CB's end feed general range is suitable for use with soft or hard solder, or brazing alloy. A solder joint is created through the principle of capillary action. When fitting and tube are heated to the correct temperature, the solder becomes molten, allowing it to be drawn into the gap between the two for a tough, reliable joint.

Center End Feed CB-EFBTC0151/2 end feed bent tap connector 15mm x 1/2in

Ideal for installation in tight spots, the Wavin Hep2O HD27 15mm x 1/2" 90° bent tap connector with brass nut and alternative rubber washer offers easy push-fit connections. Suitable for hot and cold flexible push-fit plumbing systems, this fitting is made of polybutylene (PB).

Wavin Hep2O 90° bent tap connector 15mm x 1/2in

The Yorkshire YP63 integral solder ring (ISR) 15mm x 1/2" bent tap connector is made of copper. This impermeable fitting provides protection against water supply contaminants and resists corrosion for reliable use in plumbing systems with properly installed systems expected to outlast the buildings in which they are installed. Suitable for use in a wide range of applications, this fitting incorporates an integral solder ring and has been designed for jointing copper tubes to BS EN 1057 (R220, R250 and R290). A solder joint is created through the principal of capillary action, when the fitting and tube is assembled and heated to the appropriate temperature, solder becomes molten and is drawn into the gap between tube and fitting for a durably reliable joint.

Pegler Yorkshire YP63 bent tap connector 15mm x 1/2in

PolyPlumb Enhanced is a range of reliable push-fit fittings for professional installers - newly enhanced and available for the first time in white.

Polypipe Polyplumb bent tap connector 15mm x 1/2"

Constructed for ease of handling, this Center CB 15mm x 1/2" integral solder ring (ISR) 90° bent tap connector is compact and lightweight with a smooth design to reduce flow restrictions. Ensuring a clean finish if used on exposed piping, this easy to install precision-made fitting is designed with high quality solder incorporated into each capillary socket, meaning that a reliable joint is created without the requirement to end feed. A solder joint is created through the principle of capillary action. When fitting and tube are heated to the correct temperature, the solder becomes molten, allowing it to be drawn into the gap between the two for a tough, reliable joint.

Center 635909 integral solder ring bent tap connector 15mm x 1/2in

This Polypipe Polyfit 15mm x 1/2" 90° bent tap connector is a quick-fix push-fit plumbing fitting made of polybutylene. Hand demountable, this flexible fitting is ideal for first fix use.

Polypipe Polyfit bent tap connector 15mm x 1/2"

This VSH Tectite Pro TX63/TX063 15mm x 1/2" 90° tap connector is made of brass with push-fit x BSP union nut end connections, a spigot and a washer joint. Tectite fittings from Pegler Yorkshire provide fast, cost-efficient jointing, simply pushing together to create a perfect joint in seconds.

Pegler VSH Tectite bent tap connector 15mm x 1/2"

This John Guest Speedfit push-fit 15mm x 1/2" 90° bent tap connector is designed for the connection of plastic and copper pipe. To connect, simply push the bent tap fitting fully onto the pipe and twist the plastic nut clockwise to lock in place. Where demounting is required the nut is unlocked and the collet pushed towards the body of the fitting before pulling the pipe to release. This fitting is easy to work with in confined places and removes the need for hot works on site, reducing installation time by about 40% compared to traditional fixing methods.

JG Speedfit bent tap connector 15mm x 1/2in

The Yorkshire YP63 integral solder ring (ISR) 22mm x 3/4" bent tap connector is made of copper. This impermeable fitting provides protection against water supply contaminants and resists corrosion for reliable use in plumbing systems with properly installed systems expected to outlast the buildings in which they are installed. Suitable for use in a wide range of applications, this fitting incorporates an integral solder ring and has been designed for jointing copper tubes to BS EN 1057 (R220, R250 and R290). A solder joint is created through the principal of capillary action, when the fitting and tube is assembled and heated to the appropriate temperature, solder becomes molten and is drawn into the gap between tube and fitting for a durably reliable joint.

Pegler Yorkshire bent tap connector 22mm x 3/4"

The Endex N63 copper 15mm x 1/2" bent tap connector is an end feed fitting for jointing copper tube manufactured to BS EN 1057 using soft or hard solder (brazing alloy) and is suitable for above ground hot and cold domestic or potable water services in small bore and mini bore central heating systems and low-pressure steam heating and pressurised unvented heating systems. It is equally suitable for sanitation services and compressed air lines, gas distribution systems for natural and manufactured gases, fuel oils (hard solder only) and kerosene, and engineering pipeline services that convey liquids, oils, air and gases at temperatures up to 110°C. A solder joint is created through the principal of capillary action, when the fitting and tube is assembled and heated to the appropriate temperature, solder becomes molten and is drawn into the gap between tube and fitting for a durably reliable joint.

Pegler Endex bent tap connector 15mm x 1/2"

Looking for bent tap connector? Order from Wolseley today - free delivery or click and collect available nationwide.

Bent Tap Connector